Search found 10 matches
- Sat Jun 05, 2021 4:01 am
- Forum: Maple & Maple mini etc
- Topic: reset software
- Replies: 3
- Views: 13750
reset software
is it possible to reset the board (or mcu) by code, instead of pressing the connected pin "reset" button?
- Fri Apr 23, 2021 4:37 pm
- Forum: IDE's
- Topic: upload error stm32
- Replies: 6
- Views: 4182
Re: upload error stm32
at this moment I think I have solved the problem. Monday I'll check.
I solved the problem by turning on the board by holding down the UT button, which allowed STM32cube programmer to connect to the board via STLINK, after which I reinstalled the "mini_maple_boot.bin" booloader.
I solved the problem by turning on the board by holding down the UT button, which allowed STM32cube programmer to connect to the board via STLINK, after which I reinstalled the "mini_maple_boot.bin" booloader.
- Fri Apr 23, 2021 6:23 am
- Forum: IDE's
- Topic: upload error stm32
- Replies: 6
- Views: 4182
Re: upload error stm32
now i tried with STEM32Cube programmer and with connection STLINk the error is the same.
with UART give me this error:
with UART give me this error:
Error: Activating device: KO. Please, verify the boot mode configuration and check the serial port configuration. Reset your device then try again...
- Fri Apr 23, 2021 5:59 am
- Forum: IDE's
- Topic: upload error stm32
- Replies: 6
- Views: 4182
Re: upload error stm32
the connections are OK.
- Thu Apr 22, 2021 4:37 pm
- Forum: IDE's
- Topic: upload error stm32
- Replies: 6
- Views: 4182
upload error stm32
until yesterday, using arduino ide with bluepill f103cb, i had uploaded regularly. today after some changes to the code, when I upload it gives me the following error: Sketch uses 32960 bytes (25%) of program storage space. Maximum is 131072 bytes. Global variables use 1304 bytes (6%) of dynamic mem...
- Wed Apr 21, 2021 8:53 am
- Forum: General discussion
- Topic: physical positioning break boards
- Replies: 1
- Views: 1922
physical positioning break boards
I have a doubt regarding the physical positioning of the adxl345 and hmc5883L break boards. By physical location, I mean putting the card with the sensor on a horizontal plane, or I can mount it vertically. Is it enough to swap the values of the x, y, and z axes in relation to what is printed on the...
- Sat Apr 10, 2021 5:21 pm
- Forum: Maple & Maple mini etc
- Topic: mini maple upload
- Replies: 5
- Views: 11645
Re: mini maple upload
Ok. I reset everything with stm32cubeprogrammer.
Now everything works, but I'm struggling with another kind of problem due to the mcufriend_kvb library, which I'm checking out.
anyway thank you.
Now everything works, but I'm struggling with another kind of problem due to the mcufriend_kvb library, which I'm checking out.
anyway thank you.
- Sat Apr 10, 2021 3:01 pm
- Forum: Maple & Maple mini etc
- Topic: mini maple upload
- Replies: 5
- Views: 11645
Re: mini maple upload
the card and the pin are those included in the previous link https://www.stm32duino.com/viewtopic.php?f=2&t=3 the memory should be 128k as seen at compile time Checking size .pio/build/maple_mini_origin/firmware.elf Advanced Memory Usage is available via "PlatformIO Home > Project Inspect&q...
- Sat Apr 10, 2021 8:38 am
- Forum: Maple & Maple mini etc
- Topic: mini maple upload
- Replies: 5
- Views: 11645
mini maple upload
I'm on my first and a half project with STM32. the first I tried to do it with "blue pill" with 64k, but unfortunately I ran out of memory resources, and then I switched to using the mini marple with 128k. With the blue pill everything was fine for the upload, but with the mini maple the p...
- Sat Apr 10, 2021 8:15 am
- Forum: Let us know a bit about you and your projects
- Topic: hello from Italy
- Replies: 1
- Views: 2407
hello from Italy
I am a retiree, and I studied electronics (40 years ago) and now that I have free time, I am dedicating myself to building projects using STM32 and programming simple web pages. I joined the forum hoping to have some help on my current project, (which was too big for arduino), related to an inclinom...