Search found 43 matches
- Wed Jan 24, 2024 3:03 am
- Forum: Projects
- Topic: STM32F103C8T6 custom board download issue
- Replies: 1
- Views: 2646
Re: STM32F103C8T6 custom board download issue
Don't remember if serial does verification but upload by stlink does verification, so if you don't got any error on the stlink upload everything was right with the MCU, so the problem is somewhere else, without posting an schematic are just guesses: - Boot pins is it configured right?... to boot fro...
- Wed Sep 15, 2021 9:17 am
- Forum: Off topic
- Topic: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
- Replies: 19
- Views: 8623
Re: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
@.rpv thanks! ok i'd need to fix up my blue pill 'oscilloscope' & get that 74HCTxx (on the way) :mrgreen: but SN74LVC1G17 seemed the best of them all. this and the 74HCTxx series are hcmos devices, https://www.ti.com/lit/pdf/scla007 so I'd guess it kind of says that hcmos devices are after all ...
- Tue Aug 24, 2021 12:08 am
- Forum: Off topic
- Topic: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
- Replies: 19
- Views: 8623
Re: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
So I was curious and I tried: Channel 1 (yellow) it's the DUT output, Channel 2 (green) it's the fungen, the VIN on the DUT was 5V. LM321 with no load: lm321_noload.png LM321 with 1nf capacitor as load (barely any difference): lm321_1nf.png For comparison, SN74LVC1G17 with 1nf cap as load: SN74LVC1G...
- Mon Aug 23, 2021 10:29 pm
- Forum: Off topic
- Topic: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
- Replies: 19
- Views: 8623
Re: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
The bed mosfet should be the most required to do an pwm level-up, but also it's really slow (~10hz), probably you can use an lm321/lm358/lm324 as comparator, for the heaters and fans the easiest way should be changing the mosfets: -for the heater(s) the IRLZ44N works fine with 3v3 -on fans use the A...
- Sun Aug 22, 2021 11:59 pm
- Forum: General discussion
- Topic: STM32F103C8T6 problem with EEPPROM..
- Replies: 15
- Views: 7584
Re: STM32F103C8T6 problem with EEPPROM..
Ok, first, in my experience using unsigned long it's problematic if you don't specify literally on each mention/operation Something like this should work: unsigned long x=1000000; setup(){ //...// Serial.print(x); } But I'll expect funny things on this: unsigned long x; setup(){ //...// x=1000000; S...
- Sun Aug 22, 2021 11:32 pm
- Forum: Off topic
- Topic: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
- Replies: 19
- Views: 8623
Re: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
One project that I got for about 2 years it's to make a 3d printer controller :lol: I just collected a few parts but still haven't started yet ;) 74HC125 (quad) (untested) https://www.aliexpress.com/item/32344341714.html SN74HC125 (single) (I tested this part and works nice) https://www.aliexpress.c...
- Sun Aug 22, 2021 9:55 am
- Forum: General discussion
- Topic: STM32F103C8T6 problem with EEPPROM..
- Replies: 15
- Views: 7584
Re: STM32F103C8T6 problem with EEPPROM..
You aren't posting any info or the actual errors that you're getting, but it seems that you aren't selecting the right board on the arduino ide or you core installation on the IDE may be incomplete. The eeprom libraries are supplied on both STCore and on libmaple-type cores and neither should give y...
- Sun Aug 22, 2021 9:51 am
- Forum: Off topic
- Topic: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
- Replies: 19
- Views: 8623
Re: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
Is your board like this: https://raw.githubusercontent.com/bigtreetech/ramps-1.6/master/Ramps1.6/hardware/R6%2B-SCH.pdf ? if so you can connect vcc to 3v3, all but the mosfet should work with 3v3 as VCC, you just need to level up the PWM to 5v, this also because the thermistors are connected to VCC ...
- Sat Aug 21, 2021 10:24 pm
- Forum: General discussion
- Topic: STM32F103C8T6 problem with EEPPROM..
- Replies: 15
- Views: 7584
Re: STM32F103C8T6 problem with EEPPROM..
Hi, are you using an external eeprom?, if you're using the internal flash as eeprom and if you're using the stcore you can use the standar eeprom library, no need to use external libraries, you can use the standard API: https://www.arduino.cc/en/Reference/EEPROM The libmaple variants also support th...
- Sat Aug 21, 2021 6:12 pm
- Forum: Off topic
- Topic: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
- Replies: 19
- Views: 8623
Re: 74HC(T)245 interfacing 5v cifcuits e.g. driving 5v logic level mosfets
ag123 are you using a ramps or are designing your own board? Here it's the ST STEVAL-3DP001V1 3d printer controller: https://www.st.com/en/evaluation-tools/steval-3dp001v1.html#documentation on the tab documentation, Product Specifications pdf they included the schematic. The bigtreetech brand it's...