Need advise on logic analyser

Post here first, or if you can't find a relevant section!
Posts: 78
Joined: Sun Feb 19, 2017 8:41 am

Re: Need advise on logic analyser

Post by dev » Sun Mar 19, 2017 2:08 pm

yeah, but some time it works when you changing speed from 12 to 8Mhz.

But some time controllers do weird behavior on high speed like missing of bytes.

So, that's why i was thinking to go with bit better performance as it is available.

Is that good logic analyser?

Posts: 116
Joined: Wed Nov 16, 2016 8:52 am

Re: Need advise on logic analyser

Post by david.prentice » Sun Mar 19, 2017 7:04 pm

The Logic-8 can do 8 channels at 24MHz.
The Logic-16 can do 9 channels at 32MHz. 6 channels at 50MHz.

Having never used the Logic-16, I just wonder how versatile the device is. For example, if I wanted to capture 24Mhz SPI, I would be limited to 6 channels. 32Mhz SPI would only allow 3 channels. SPI would need at least 4 channels.

So I would be more interested in a device that can sample 8 channels at more than 50M.
If it has compression, it can handle typical sequences even if they are a second or two.


User avatar
Posts: 7680
Joined: Mon Apr 27, 2015 10:36 am
Location: Melbourne, Australia

Re: Need advise on logic analyser

Post by RogerClark » Wed Mar 22, 2017 6:59 am

I have a logic-8 and logic-16 (clones), and the 16 only works at 100Mhz if you have 2 channels

It drops to 50Mhz for 3 or 4 channels.

I think it drops to 25Mhz if you have more than 4 channels (though I can't totally remember)

If you want to look at SPI then 4 channels should be enough, even if you need the SS / CE pin. So you will get 50Mhz which is faster than the STM32 is capable of running at.

In hindsight, I should have probably spent a bit extra and get one of those FPGA based analysers rated at
4 channels @ 400 MHZ
8 channels @ 200 MHZ
16 channels @ 100 MHZ
But they are around $75USD which is twice what I paid for the logic-16 clone

And I've no idea how good the software for the FPGA based analysers is.

Posts: 116
Joined: Wed Nov 16, 2016 8:52 am

Re: Need advise on logic analyser

Post by david.prentice » Wed Mar 22, 2017 7:58 am

I think that that was my conclusion. i.e. 24MS Logic-8 or 200MS FPGA type.

Does anyone have experience of the FPGA type? Which model and price?
Which software?

I have been very happy with the Logic-8. Somehow the Logic-16 does not offer much more speed.
I want 8 channels. I doubt if 16 channels are often used and lower sample rate would be ok..


User avatar
Posts: 1729
Joined: Sat Mar 26, 2016 3:26 pm
Location: Rapa Nui

Re: Need advise on logic analyser

Post by Pito » Wed Mar 22, 2017 8:57 am

The FPGA based LAs work fine. All >50Msps LAs today work FPGA-way. See my post above - Logic Sniffer (OLS) - that is an FPGA 200Msps based LA.

Important part of an FPGA based LA is the verilog/vhdl FPGA frontend ("FPGA bitstream") and the PC backend ("client sw"). They are opensourced usually. Double check whether the community supports you with updates frequently.

PS: this seems to me the most important point. For example the OLS LA is considered "mature", it simply works, no update at FPGA side for 5y+, the PC backend gets aprox 1 small update per year.
The new DSLogic LA has been reviewed as ie. "the hw is unbeatable", but the PC backend "needs improvements".

The OLS samples into its internal FPGA memory only, but uses RLE compression, so even with its 24kB internal RAM you may capture longer sequences.

The DSlogic's LA is a modern variant of the OLS with an external DRAM (and a larger FPGA), and maybe it possess an USB streaming capability (to store the data on the PC online).

Basically the fastest sampling rates get into the internal FPGA RAM, medium sampling rates could be stored into the external DRAM, and the slowest could be saved on the PC continuously (ie serial UART or I2C captures).

OLS uses the older Spartan3 FPGA with DDR sampling (8channels, 200Msps max), the DSLogic uses Spartan6 probably DDR sampling too (4 channels, max 400Msps). At highest sampling rates both save the data into internal FPGA RAM.

"200Msps" means you can observe signals with H or L ~10ns long with a good resolution. A "good resolution" means there will be always 5ns uncertainty at that sampling rate of course (because 1/200M = 5ns) - in practice it means a 50Mhz 50/50 waveform will have the L or H 10ns +/- 5ns on the screen. You can see even a single 5ns pulse or 100MHz pulse train if the sampling hits the pulses exactly. That is for OLS.
With DSLogic the stuff works theoretically twice better, but I've never seen any practical review on that, however.

OLS has got a simple fixed level HCMOS buffer which is 5V tolerant at its input. No special protection or matching circuitry at the input. No special probes, just plain flying wires.

The DSLogic's LA claims they can set the input logic threshold with a DAC? (double check for the latest version), and they wired some protection and impedance matching at the LA inputs. That may decrease the bandwidth, however. Also the probes seem to be shielded.

For example the resolution of the OLS is up to 5ns. And it works. Mind the measurements at such speeds needs a good understanding of what you actually do (wire lengths, impedance matching, ..).
The LA's with higher sampling rates are useful for people who mess with CPLD/FPGAs, memories, custom logic, etc. and who are chasing edges, glitches, collisions, ringing, etc.
PS: of course you may do similar measurements with the popular low-cost oscilloscopes today, but still the price of these low-cost FPGA based LAs is <<10% of the cheapest o'scope price with similar capabilities.

Here as an example the OLS forum
and DSLogic one
and an attempt to create an open source platform for all LA's :) ... _analyzers

PS: There is a lot of LAs available (the above sigrok link indicates 50+ LAs), I do not advertise the OLS or the DSLogic as THE one, just using them as an example of "talented FPGA based LAs" for a very good price (almost nil compared to a professional LA equipment with similar params). I purchased the OLS maybe 7y back, I had a lot of fun with it, it helped me many times, and I still consider it one of my bests buy's..
Pukao Hats Cleaning Services Ltd.

User avatar
Posts: 1241
Joined: Mon Apr 27, 2015 1:45 pm

Re: Need advise on logic analyser

Post by martinayotte » Wed Mar 22, 2017 2:07 pm

I'm using this 24MHz since awhile
But the current thread here make my old wish coming back to my mind.
I will purchase either one of those : iCE40-HX1K iCEstick Eval Board or Open Workbench Logic Sniffer.
Here some stuff to read about : ... er-for-22/ ... er-for-22/ ... ic_Sniffer ... l?cPath=75

Posts: 205
Joined: Thu Feb 25, 2016 7:27 pm

Re: Need advise on logic analyser

Post by Ollie » Wed Mar 22, 2017 2:21 pm

I used to have Saleae Logic 16. It had very nice functionality, but for some cases the speed was not enough. I did upgrade to Saleae Logic Pro 16 and have not regretted the high price. The combined analysis of high speed analog data with logic data is very useful. The other nice feature is the support for low voltage (1.2V and 1.8V) logic.

User avatar
Posts: 1729
Joined: Sat Mar 26, 2016 3:26 pm
Location: Rapa Nui

Re: Need advise on logic analyser

Post by Pito » Wed Mar 22, 2017 4:56 pm

FYI - the OLSniffer started 2009 or 2010, with a firmware for the pic (the communication between FPGA and PC), with initial version of the bitstream for FPGA (Sump protocol?), and an SUMP client (I never used it). Then, a group of enthusiastic experts, started to develop a new FPGA bitstream, and a new client sw. Most notably:

1. "Dogsbody" did (details on his HP16500/HP16550 style triggers built into the Demon core):
and I highly recommend this reading:
to anybody who feels himself ambitious enough to develop his own LA's FPGA front end ;)

2. Jawi still supports the client:

So in order to get the latest you have to:
1. flash the latest pic software
2. upload the latest Demon FPGA core bitstream
3. use the latest jawi's OLS client sw.

BTW, the development of the above ingredients took several years since the initial OLS introduction.

The jawi's client does not support all the existing built-in Demon core functionality yet - ie the advanced HP16550 triggering, there are guys who tried to enhance the client sw with such a support, not sure how it ended up, though: ... =57&t=8548 ... 57a9afe61f
Pukao Hats Cleaning Services Ltd.

User avatar
Posts: 1718
Joined: Mon Apr 27, 2015 11:04 pm
Location: Sunny Scotland

Re: Need advise on logic analyser

Post by ahull » Fri Dec 22, 2017 1:14 pm

just thought this might be an appropriate place to drop this link. For those who like their Logic Analysers small... ;) ... use-sigrok


- Andy Hull -

Posts: 1674
Joined: Wed Jul 08, 2015 2:09 pm
Location: St Annes, Lancs,UK

Re: Need advise on logic analyser

Post by zmemw16 » Fri Dec 22, 2017 4:12 pm

suffice to say i have 3 off OLS, more if i they had a good price :)
never any issues, reliable, solid behaviour, all over excellent.

Post Reply